(Samples of DNAs of known size are
typically generated by restriction enzyme digestion of a plasmid or
bacteriophage DNA of known sequence). The equipment and supplies necessary for conducting agarose gel electrophoresis are relatively simple and include:
An electrophoresis chamber and power supply.
Gel casting trays, which are available in a variety of sizes and composed of UV-transparent plastic.
Sample combs, around which molten agarose is poured to form sample wells in the gel.
Electrophoresis buffer, usually Tris-acetate-EDTA (TAE) or Tris-borate-EDTA (TBE).
Loading buffer, which contains something dense
(e.g. glycerol) to allow the sample to "fall" into the sample wells, and
one or two tracking dyes, which migrate in the gel and allow visual
monitoring or how far the electrophoresis has proceeded.
Ethidium bromide, a fluorescent dye used for staining nucleic acids.
Transilluminator (an ultraviolet light box), which is used to visualize ethidium bromide-stained DNA in gels.
NOTE: Always wear protective eyewear when observing DNA on a Transilluminator to prevent damage to the eyes from UV light.
For this we take 2ml of TAE stock solution in an Erlenmeyer flask
and make the volume to 100ml by adding 98ml of distilled water. The 1x
working solution is 40 mM Tris-acetate/1 mM EDTA
It is important to use the same batch of electrophoresis buffer in both the electrophoresis tank and the gel preparation.
For this usually 2 grams of agarose is added to 100ml of electrophoresis buffer.
Agarose Concentration in Gel (% [w/v])
(The gel should be between 3 - 5 mm thick. Check that no air bubbles are under or between the teeth of the comb.)
Prepare a 50x stock solution of TAE buffer in 1000m of distilled H2O:
For this weigh 242 g of Tris base in a chemical balance. Transfer this to a 1000ml beaker.
Prepare EDTA solution (pH 8.0, 0.5M) by weighing 9.31g of EDTA and
dissolve it in 40ml distilled water. EDTA is insoluble and it can be
made soluble by adding sodium hydroxide pellets. Check the pH using pH
meter. Make the solution 100ml by adding distilled water.
Pipette out 57.1 ml of glacial acetic acid.
Mix the Tris base, EDTA solution and glacial acetic acid and add distilled water to make the volume to 1000ml
Prepare sufficient electrophoresis buffer (usually 1x TAE ) to fill the electrophoresis tank and to cast the gel:
Prepare a solution of agarose in electrophoresis buffer at an appropriate concentration:
Loosely plug the neck of the Erlenmeyer flask. Heat the slurry in a
boiling-water bath or a microwave oven until the agarose dissolves. The
agarose solution can boil over very easily so keep checking it. It is
good to stop it after 45 seconds and give it a swirl. It can become
superheated and NOT boil until you take it out whereupon it boils out
all over you hands. So wear gloves and hold it at arm's length. You can
use a Bunsen burner instead of a microwave - just remember to keep
Use insulated gloves or tongs to transfer the flask/bottle into a
water bath at 55°C. When the molten gel has cooled, add 0.5µg/ml of
ethidium bromide. Mix the gel solution thoroughly by gentle swirling.
(For the preparation of ethidium bromide adds 1 g of ethidium bromide to 100 ml of H2O.
Stir on a magnetic stirrer for several hours to ensure that the dye has
dissolved. Wrap the container in aluminum foil or transfer the 10 mg/ml
solution to a dark bottle and store at room temperature.)
While the agarose solution is cooling, choose an appropriate comb for forming the sample slots in the gel.
Pour the warm agarose solution into the mold.
Allow the gel to set completely (30-45 minutes at room
temperature), then pour a small amount of electrophoresis buffer on the
top of the gel, and carefully remove the comb. Pour off the
electrophoresis buffer. Mount the gel in the electrophoresis tank.
Add just enough electrophoresis buffers to cover the gel to a depth of approx. 1mm.
Mix the samples of DNA with 0.20 volumes of the desired 6x gel-loading buffer.
Slowly load the sample mixture into the slots of the submerged gel
using a disposable micropipette or an automatic micropipettor or a
drawn-out Pasteur pipette or a glass capillary tube. Load size standards
into slots on both the right and left sides of the gel.
Close the lid of the gel tank and attach the electrical leads so
that the DNA will migrate toward the positive anode (red lead). Apply a
voltage of 1-5 V/cm (measured as the distance between the positive and
negative electrodes). If the electrodes are 10cm apart then run the gel
at 50V. It is fine to run the gel slower than this but do not run it any
faster. Above 5V/cm the agarose may heat up and begin to melt with
disastrous effects on your gel's resolution. If the leads have been
attached correctly, bubbles should be generated at the anode and
Run the gel until the bromophenol blue and xylenecyanol FF have migrated an appropriate distance through the gel.
(The presence of ethidium bromide allows the gel to be examined by UV illumination at any stage during electrophoresis).
The gel tray may be removed and placed directly on a
transilluminator. When the UV is switched on we can see orange bands of
Procedure for operating the virtual lab:
Check whether you have done all the steps listed below:
Prepare TAE buffer.
Transfer 100ml of the buffer to a conical flask.
Weigh 2grams of agarose and add to the 100ml buffer solution.
Keep in oven.
Take the solution from oven.
Add ethidium bromide.
Pour the solution to a gel caster.
Place the comb.
Pour the 100ml buffer solution to the electrophoretic chamber.
Place the gel in the caster in the electrophoretic chamber.
Connect the electrodes and switch on the current.
Switch off the power supply.
Remove the gel from the electrophoretic chamber.
Place the gel in the UV Transilluminator.
Switch on the Transilluminator.
Ethidium bromide is a mutagen and should be handled as a hazardous chemical (so wear gloves while handling)
DIFFERENCES ENCOUNTERED IN REAL LABORATORY:
Make sure that the Agarose is fully dissolved in the buffer. If it
is not dissolved well, again melt it some more time to dissolve
Before casting the gel, the tray and comb should wipe with ethanol.
Make sure that the gel in the Chamber is immersed in the TAE Buffer.
Labelings should be proper.
Ensure that the connections should be proper.
Before the incubation step, ensure that the water bath is set at the correct temperature that we required or not.
Unfortunately, this Virtual Lab requires
Adobe Flash player. Please see additional information if this does not
work on your computer